NB/T 11443-2023 可控起动传动装置通用技术条件

ICS73.100.40

CCSD93

中华人民共和国能源行业标准

NB/T11443—2023

可控起动传动装置通用技术条件

Generaltechnicalspecificationofcontrolledstarttransmission

2023⁃12⁃28发布2024⁃06⁃28实施

国家能源局发布

中国标准出版社出版

NB/T11443—2023

目次

前言··························································································································Ⅲ

1范围·······················································································································1

2规范性引用文件········································································································1

3术语和定义··············································································································1

4型式与命名··············································································································2

5要求·······················································································································4

6试验方法·················································································································8

7检验规则···············································································································11

8标志、包装、运输和贮存·····························································································12

附录A（资料性）背对背对拖试验系统············································································14

附录B（资料性）直接拖动试验系统···············································································15

Ⅰ

NB/T11443—2023

前言

本文件按照GB/T1.1—2020《标准化工作导则第1部分：标准化文件的结构和起草规则》的规

定起草。

请注意本文件的某些内容可能涉及专利。本文件的发布机构不承担识别专利的责任。

本文件由中国煤炭工业协会提出。

本文件由煤炭行业煤矿专用设备标准化技术委员会归口。

本文件起草单位：中国煤炭科工集团太原研究院有限公司、太原煤科检测技术有限公司、山西天地

煤机装备有限公司、安标国家矿用产品安全标志中心有限公司、山西维达传动科技有限公司、宁夏天地

奔牛实业集团有限公司、中煤张家口煤矿机械有限责任公司。

本文件主要起草人：刘伟立、王步康、金江、石岚、师理智、李志忠、史志远、宋岩、贺江波、宋磊、贾炎、

庄占斌、李海锋、陈昭赫、赵永红、张学瑞、王彩君、马柯峰、刘志、宋如斋。

Ⅲ

NB/T11443—2023

可控起动传动装置通用技术条件

1范围

本文件规定了可控起动传动装置（以下简称可控传动系统）的型式与命名、要求、试验方法、检验规

则、标志、包装、运输和贮存。

本文件适用于煤矿井下刮板输送机用可控传动系统、带式输送机用可控传动系统的设计、制造与

检验。

2规范性引用文件

下列文件中的内容通过文中的规范性引用而构成本文件必不可少的条款。其中，注日期的引用文

件，仅该日期对应的版本适用于本文件；不注日期的引用文件，其最新版本（包括所有的修改单）适用于

本文件。

GB/T3683橡胶软管及软管组合件油基或水基流体适用的钢丝编织增强液压型规范

GB/T3836.1爆炸性环境第1部分：设备通用要求

GB/T3836.2爆炸性环境第2部分：由隔爆外壳“d”保护的设备

GB/T3836.3爆炸性环境第3部分：由增安型“e”保护的设备

GB/T3836.4爆炸性环境第4部分：由本质安全型“i”保护的设备

GB/T3836.9爆炸性环境第9部分：由浇封型“m”保护的设备

GB/T10544橡胶软管及软管组合件油基或水基流体适用的钢丝缠绕增强外覆橡胶液压型规范

GB/T13306标牌

AQ1043—2007矿用产品安全标志标识

JB/T7929齿轮传动装置清洁度

MT/T98液压支架用软管及软管总成检验规范

MT/T148刮板输送机用减速器

MT/T210煤矿通信、检测、控制用电工电子产品基本试验方法

MT/T681煤矿用带式输送机用减速器技术条件

MT818.1煤矿用电缆第1部分：移动类软电缆一般规定

MT/T818.14煤矿用阻燃电缆第3单元：煤矿用阻燃通信电缆

3术语和定义

下列术语和定义适用于本文件。

3.1

可控起动传动装置controlledstarttransmission

基于微处理器为核心的多级齿轮减速器、湿式离合器及液压控制组成的传动系统。

3.2

自动保护（自动监控）装置auto-protection（automaticmonitoring）system

用于采集、处理可控传动系统在启动、运行、停止过程中的相关状态参数，在相关参数出现异常时

1